用戶在進行紡織類試樣燃燒性能的測試的時候需要了解GB5455中的基本要求。北京鑫生卓銳科技有限公司的紡織品垂直燃燒測定儀,依據國家標準GB/T5455-2014《紡織品 燃燒性能 垂直放行 損毀長度、陰燃和續燃時間的測定》規定的技術要求設計制造,與儀器相比,該設備可自動記錄試驗時間,具有自動化程度高、記時準確、自動顯試結果、試驗數據可存儲、可調閱試驗歷史數據等優點,與專用的式樣支架配合,火焰火源點燃后,測定式樣的燃燒速度,有焰燃燒和無焰燃燒時間。該儀器適用于安全網、防護服裝、安全帶等各類織物及其制品,最終適用于GB5455-2014標準中規定的垂直方向紡織品底邊點火時燃燒性能的試驗方法。
試樣調濕與干燥
條件A:試樣放置在GB6529規定的標準大氣條件下前行調濕,然后將調濕后的試樣放入密封容器內。
條件B:將試樣置于(105±3)℃的烘箱內干燥(30±2)min取出,放置在干燥器中冷卻。冷卻時間不少于30min。且條件A和條件B所測結果不具可比性。
試樣制備
根據上述章節規定調濕條件準備試樣:
條件A:尺寸為300mm*89mm,經(縱)向取5塊,緯(橫)向取5塊,共10塊試樣。
條件B:尺寸為300mm*89mm,經(縱)向取3塊,緯(橫)向取2塊,共5塊試樣。
取樣位置:剪取試樣時距離布邊至少100mm,試樣的兩邊分別與織物的經(縱)向和緯(橫)向平行,試樣表面應無沾污,污褶皺。經向試樣不能取自同一經紗,緯向試樣不能取自同一緯紗。如果測試制品,試樣中可包含接縫或裝飾物。
結果計算
根據章節三調濕條件,計算結果:
條件A:分別計算經(縱)向、緯(橫)向5快試樣的續燃時間、陰燃時間和損毀長度的平均值,結果精確至0.1S和1mm。
條件B:計算5塊試樣的續燃時間、陰燃時間和損毀長度的平均值,結果精確至0.1S和1mm。
北京鑫生卓銳科技有限公司供應整理。